Question No. 1

How can you minimize unicast flooding in a network?

• A. Configure HSRP on two routers, with one subnet preferred on the first router and different subnet preferred on the second router.
• B. Set the router’s ARP timeout value to be the same as the timeout value for Layer forwarding table entries.
• C. Set the router’s ARP timeout value to greater than the timeout value for Layer 2 forwarding table entries.
• D. Set the router’s ARP timeout value to less than the timeout value for Layer 2 forwarding table entries.

Question No. 2

A network engineer is enabling conditional debugging and execute two command. Debug condition interfaces serial00 and debug condition interfaces serial 0/1. Which debugging output is displayed as a result?

• A. interface cannot be used as a debug condition.
• B. Output is display for both specified interfaces.
• C. Output is display for interface serial 0/1 only.
• D. Output is display for interface 0/0 only.

Question No. 3

Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose three)

• A. header compression
• B. explicit congestion notification
• C. keepalive
• D. time stamps
• E. TCP path discovery
• F. MTU window

Question No. 4

SIMULATION

You are a network engineer with ROUTE.com, a small IT company. They have recently merged two organizations and now need to merge their networks as shown in the topology exhibit. One network is using OSPF as its IGP and the other is using EIGRP as its IGP. R4 has been added to the existing OSPF network to provide the interconnect between the OSPF and EIGRP networks. Two links have been added that will provide redundancy.

The network requirements state that you must be able to ping and telnet from loopback 101 on R1 to the OPSF domain test address of 172.16.1.100. All traffic must use the shortest path that provides the greatest bandwidth. The redundant paths from the OSPF network to the EIGRP network must be available in case of a link failure. No static or default routing is allowed in either network.

A previous network engineer has started the merger implementation and has successfully assigned and verified all IP addressing and basic IGP routing. You have been tasked with completing the implementation and ensuring that the network requirements are met. You may not remove or change any of the configuration commands currently on any of the routers. You may add new commands or change default values.

• A. Check the E part for details answer.
• B. Check the E part for details answer.

Question No. 5

Refer to the exhibit.

Which LSA type does R3 propagate into Area 1 for the 192.168.10.0/24 network?

• A. type 3 LSA
• B. type 5 LSA
• C. type 7 LSA
• D. type 10

Question No. 6

which phase of dmpvn spoke to spoke communications?

• A. phase2
• B. phase4C
• C. phase5
• D. phase6
• E. phase1

Question No. 1

You are configuring a static route. Which action must you take to avoid the possibility of recursive row

• A. Use the ip route command to specify the next-hop IP address only
• B. Specify the next hop on a directly connected interface
• C. Use the ip route command to specify both the next-hop IP address and the connected
• D. Use the ip route command to specify the connected interface only

Question No. 2

Regarding a diagram with 3 routers (H1(with IPv6 IP and Loopback 1.1.1.1) +R1 (with IP IPv6 and Loopback

2.2.2.2) +R2 (with IP IPv6 and Loopback 3.3.3.3)

running with EIGRP 100 on both routers and what command you will implement so that you will see the

loopback IP of R2 to be advertised at H1

• A. H1(config t)#router eigrp 100
• B. R2(config t)#router eigrp 100
• C. H1(config t)#ipv6 router eigrp 100
• D. R2(config t)#ipv6 router eigrp 100

Question No. 3

What is the advertised distance for the 192.168.46.0 network on R1?

• A. 333056
• B. 1938688
• C. 1810944
• D. 307456

Question No. 4

Refer to the exhibit.

Router 1 cannot ping router 2 via the Frame Relay between them. Which two statements describe the problems? (Chooses two.)

• A. encapsulation is mismatched.
• B. Frame Relay map is configured.
• C. DLCI is active.
• D. DLCI is inactive or deleted.
• E. An access list is needed to allow ping.

Question No. 5

Which two features were added in MSCHAP version 2?(choose 2)

• A. Mutual authentication between peers.
• B. Using the MD5 hash for stronger security
• C. Using three-way handshakes for authentication.
• D. Ability to change an expired password
• E. Backward-compatibility with MSCHAP version 1.