Real N10-006 CompTIA Networks Exam Question Samples For Free

TestActual is providing N10-006 exam preparation material for CompTIA Network+ N10-006 exam for last 10 years and has gathered more then 50,000+ satisfied customers around the world. Our success rate for CompTIA Network+ N10-006 exam is remarkable. You may try the free demo of our CompTIA Network+ N10-006 exam dumps material, before purchase. We provide you latest N10-006 exam questions. The candidates will also be entitled 90 days free updates.

♥♥ 2018 NEW RECOMMEND N10-006 Exam Questions ♥♥

N10-006 exam questions, N10-006 PDF dumps; N10-006 exam dumps:: (461 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate CompTIA N10-006 Dumps Exam Questions and Answers:

Version: 15.0
Question: 21

After connecting a workstation directly to a small business firewall, a network administrator is trying to manage it via HTTPS without losing its stored configuration. The only two pieces of information that the network administrator knows about the firewall are the management interface MAC address, which is 01:4a:d1:fa:b1:0e, and the administrator’s password. Which of the following will allow the administrator to log onto the firewall via HTTPS if the management’s IP address is unknown and the administrator’s workstation IP address is

A. Use the reset button on the back of the firewall to restore it to its factory default, and then log onto
B. Run the following command on the administrator’s workstation: arp –s 01:4a:d1:fa:b1:0e
C. Use an SNMP tool to query the firewall properties and determine the correct management IP address
D. Use a crossover cable to connect to the console port and reconfigure the firewall management IP to

Answer: B

Address Resolution Protocol (ARP) is used to resolve IP addresses to MAC addresses. The arp –s command addsa static permanent address to the ARP cache. This will allow the administrator to access the firewall.

Question: 22

A network technician has detected a personal computer that has been physically connected to the corporate network. Which of the following commands would the network technician use to locate this unauthorized computer and determine the interface it is connected to?

A. nbtstat –a
B. show mac address-table
C. show interface status
D. show ip access-list
E. nslookup hostname

Answer: B

The show mac address-table command is used to view the ageing timer, and also the unicast and multicast MAC addresses stored in the MAC address table by the switch. Furthermore, you can view all of the addresses in the table or only the addresses learned or specified on a particular port or VLAN.

Question: 23

Which of the following network devices use ACLs to prevent unauthorized access into company systems?

B. Firewall
C. Content filter
D. Load balancer

Answer: B

A firewall is a system designed to prevent unauthorized access to or from a private network. Firewalls arefrequently used to prevent unauthorized Internet users from accessing privatenetworks connected to the Internet, especially intranets. Firewalls use ACLs (access control lists) to determine which traffic is allowed through the firewall. All traffic entering or leaving the intranet passes through the firewall, which examines each message and blocks or allows the message depending on rules specified in the ACL. The rules in the ACL specify which combinations of source IP address, destination address in IP port numbers are allowed.

Question: 24

Which of the following is used to define how much bandwidth can be used by various protocols on the network?

A. Traffic shaping
B. High availability
C. Load balancing
D. Fault tolerance

Answer: A

If a network connection becomes saturated to the point where there is a significant level of contention, network latency can rise substantially.
Traffic shaping is used to control the bandwidth used by network traffic. In a corporate environment, business-related traffic may be given priority over other traffic. Traffic can be prioritized based on the ports used by the application sending the traffic. Delayed traffic is stored in a buffer until the higher priority traffic has been sent.

Question: 25

Which of the following is used to authenticate remote workers who connect from offsite? (Select TWO).

B. VTP trunking
C. Virtual PBX
E. 802.1x

Answer: D,E

D: A RADIUS (Remote Authentication Dial-in User Service)server is a server with a database of user accounts and passwords used as a central authentication database for users requiring network access. RADIUS servers are commonly used by ISP’s to authenticate their customer’s Internet connections.
Remote users connect to one or more Remote Access Servers. The remote access servers then forward the authentication requests to the central RADIUS server.
E: 802.1X is an IEEE Standard for Port-based Network Access Control (PNAC). It provides an authentication mechanism to devices wishing to attach to a network.
802.1X authentication involves three parties: a supplicant, an authenticator, and an authentication server. The supplicant is a client that wishes to attach to the network. The authenticator is a network device,such as an Ethernet switch, wireless access point or in this case, a remote access server and the authentication server is the RADIUS server.

Question: 26

Which of the following provides accounting, authorization, and authentication via a centralized privileged database, as well as, challenge/response and password encryption?

A. Multifactor authentication
D. Network access control

Answer: C

TACACS+ (Terminal Access Controller Access-Control System Plus) is aprotocol that handles authentication, authorization, and accounting (AAA) services. Similar to RADIUS, TACACS+ is a centralized authentication solution used to provide access to network resources. TACACS+ separates the authentication, authorization, and accounting services enabling you to host each service on a separate server if required.

New Updated N10-006 Exam Questions N10-006 PDF dumps N10-006 practice exam dumps: